Highlighted Features
Lightning protection - no long signal wires, and electronics are shielded in a titanium housing for use in saltwater
HOBOware Pro software provides easy conversion to accurate water level reading, fully compensated for barometric pressure temperature, and water density.
Multiple-rate sampling allows faster sampling at critical times such as when pumping starts or stops.
Available in 4 depth ranges
Ideal for use in wells, streams, lakes, wetlands and tidal areas
No-vent-tube design for easy reliable deployment
Available in stainless and titanium versions
Durable ceramic pressure sensor
3-point NIST-traceable calibration certificate included
The U20-001-03-Ti data logger supports the following measurements: Absolute Pressure, Barometric Pressure, Temperature and Water Level
| Pressure and Water Level Measurements U20-001-03 and U20-001-03-Ti |
| Operation Range |
0 to 850 kPa (0 to 123.3 psia); approximately 0 to 76.5 m (0 to 251 ft) of water depth at sea level, or 0 to 79.5 m (0 to 262 ft) of water at 3,000 m (10,000 ft) of altitude |
| Factory Calibrated Range |
69 to 850 kPa (10 to 123.3 psia), 0° to 40°C (32° to 104°F) |
| Burst Pressure |
1200 kPa (174 psia) or 112 m (368 ft) depth |
| Water Level Accuracy* |
Typical error: ±0.05% FS, 3.8 cm (0.125 ft) water
Maximum error: ±0.1% FS, 7.6 cm (0.25 ft) water |
| Raw Pressure Accuracy** |
±0.3% FS, 2.55 kPa (0.37 psi) maximum error |
| Resolution |
<0.085 kPa (0.012 psi), 0.87 cm (0.028 ft) water |
| Pressure Response Time (90%)*** |
<1 second; measurement accuracy also depends on temperature response time |
| Temperature Measurements (All Models) |
| Operation Range |
-20° to 50°C (-4° to 122°F) |
| Accuracy |
±0.44°C from 0° to 50°C (±0.79°F from 32° to 122°F), see Plot A in manual |
| Resolution |
0.10°C at 25°C (0.18°F at 77°F), see Plot A in manual |
| Response Time (90%) |
5 minutes in water (typical) |
| Stability (Drift) |
0.1°C (0.18°F) per year |
| Logger |
| Real-time Clock |
± 1 minute per month 0° to 50°C (32° to 122°F) |
| Battery |
2/3 AA, 3.6 Volt lithium, factory-replaceable |
| Battery Life (Typical Use) |
5 years with 1 minute or greater logging interval |
| Memory (Non-volatile) |
64K bytes memory (approx. 21,700 pressure and temperature samples) |
| Weight |
Stainless steel models: approximately 210 g (7.4 oz)
Titanium models: approximately 140 g (4.8 oz) |
| Dimensions |
2.46 cm (0.97 inches) diameter, 15 cm (5.9 inches) length; mounting hole 6.3 mm (0.25 inches) diameter |
| Wetted Materials |
Titanium, Viton® o-rings, acetyl cap, ceramic sensor |
| Logging Interval |
Fixed-rate or multiple logging intervals, with up to 8 user-defined logging intervals and durations; logging intervals from 1 second to 18 hours. Refer to the HOBOware software manual. |
| Launch Modes |
Immediate start and delayed start |
| Offload Modes |
Offload while logging; stop and offload |
| Battery Indication |
Battery voltage can be viewed in status screen and optionally logged in datafile. Low battery indication in datafile. |
| Environmental Rating |
IP68 |
|
 |
The CE Marking identifies this product as complying with all relevant directives in the European Union (EU). |
* Water Level Accuracy: With accurate reference water level measurement, known water density, accurate Barometric Compensation Assistant data, and a stable temperature environment.
** Raw Pressure Accuracy: Absolute pressure sensor accuracy includes all sensor drift, temperature, and hysteresis-induced errors.
*** Changes in Temperature: Allow 10 minutes in water to achieve full temperature compensation of the pressure sensor. Maximum error due to rapid thermal changes is approximately 0.5%.
