Current/Voltage

12-bit 4-20mA Input Adapter...
Product available with different options
Home

12-bit 4-20mA Input Adapter Sensor

Onset
S-CIA-CM14
The 12-bit 4-20 mA Input Adapter interfaces with any sensor providing a 4-20 mA signal to connect to smart sensor compatible HOBO stations. This adapter features both a non-switched input and a battery-saving switched input that extends the life of external batteries. It also provides a trigger signal for controlling power to attached external sensors,...
View
FlexSmart TRMS Module (2...
Available
Home

FlexSmart TRMS Module (2 channels) w/modular plug Sensor

Onset
S-FS-TRMSA-D
€101.00
The 15-bit two-channel FlexSmart True RMS Current / Voltage Module accepts an input range of 5mV to 512mV and is compatible with 333mV FS output sensors. Field wiring is 2-wire via screw terminals.NOTE: If using the S‐FS‐TRMSA‐D with a U30‐GSM or RX3003-00-01, the S‐FS‐TRMSA‐D should be located approximately 1 meter (3 ft) from the U30 in order to avoid...
EG4100 Series Current...
Product available with different options
Home

EG4100 Series Current Transformer Sensor

Onset
T-EG-xxxx-xxxx
Split-core CTs from J&D Sensing offer a well constructed hinged body and are accurate to +/-1% from 1%-100% of their stated current rating. The small interval for physical size options (10mm/0.39", 24mm/0.94", and 36mm/1.42") allow for a flexible installation. Each CT size has a hinge and clipping mechanism, making it easy to close the CT in tight...
View
E50B2 Power & Energy Meter... E50B2 Power & Energy Meter... 2
Product available with different options
Home

E50B2 Power & Energy Meter Sensor

Onset
T-VER-E50B2
Build better energy efficiency and power management with the E50B2 Power & Energy Meter. This cost-effective sensor is simple to deploy and can either be installed on standard DIN rail or be surface mounted. The E50B2 integrates with HOBO UX, U30, ZW, H22, and H21 data loggers.
View
300 Volt AC Potential...
Product available with different options
Home

300 Volt AC Potential Transformer Sensor

Onset
T-MAG-SPT-300
The Magnelab 300-Volt AC Potential Transformer is used with the FlexSmart TRMS Module to provide accurate measurement of AC voltage. One or two PTs can be used with each FlexSmart TRMS module. This sensor offers an accuracy of ±1% (from 10% to 130% of rated voltage), but because this transformers ties directly into the line, it should be used only by...
View
600 Volt AC Potential...
Out of stock
Home

600 Volt AC Potential Transformer Sensor

Onset
T-MAG-SPT-600
The Magnelab 600-Volt AC Potential Transformer is used with the FlexSmart TRMS Module to provide accurate measurement of AC voltage. One or two PTs can be used with each FlexSmart TRMS module. This sensor offers an accuracy of ±1% (from 10% to 130% of rated voltage), but because this transformers ties directly into the line, it should be used only by...
View
12-bit Voltage Input...
Available
Home

12-bit Voltage Input Adapter Sensor

Onset
S-VIA-CM14
€76.00
The 12-bit Voltage Input Adapter interfaces with sensors providing 0-5 VDC signals to act as a smart sensor with compatible data loggers. This adapter features both a non-switched input and a battery-saving switched input that extends the life of external batteries. It also provides a trigger signal for controlling power to attached external sensors,...
Split-core AC current...
Product available with different options
Home

Split-core AC current Sensor ( Available in 5 ranges - 20, 50, 100, 200 & 600 Amps)

Onset
CTV-x
A split-core AC current sensor records AC amperage for use with U12 Series, UX120-006M and ZW Series of data loggers with external input channels. With an input current of AC current, sine wave, single phase 50 Hz or 60 Hz, load power factor 0.5 to 1.0 lead or lag.The molded-plastic housing is rated for indoor use per UL508.
View
Rogowski Coil Sensor...
Product available with different options
Home

Rogowski Coil Sensor (T-EG-4000-2775 and T-EG-7000-2775)

Onset
T-EG-x000-2775
Rope CTs are excellent for bus-bars and large switch-gear applications. Self-powered rope CTs are flexible and easy to install, but will not be accurate below 30A. Each CT includes the two-pin CT connector plug.
View
0 to 10 VoltsDC Voltage...
Product available with different options
Home

0 to 10 VoltsDC Voltage Input Sensor

Onset
CABLE-ADAP10
The CABLE-ADAP10 is an external input cable providing analog sensor input of 0-10 Vdc max. for HOBO ZW Series data nodes, UX120, and U12 series data loggers with one or more analog inputs. The cable has 13mm tinned braided wire leads and a total length 1.9m.
View
0 to 5 VoltsDC Voltage...
Product available with different options
Home

0 to 5 VoltsDC Voltage Input Sensor

Onset
CABLE-ADAP5
The CABLE-ADAP5 is an external input cable providing analog sensor input of 0-5 Vdc max. for HOBO ZW Series data nodes, UX120, and U12 series data loggers with one or more analog inputs. The cable has 13mm tinned braided wire leads and a total length 1.9m.
View
0 to 2.5 VoltsDC Voltage...
Product available with different options
Home

0 to 2.5 VoltsDC Voltage Input Sensor

Onset
CABLE-2.5-STEREO
An external input cable with 13mm tinned braided wire leads. Voltage input specifications vary with attached data logger.Overall length of this cable is 1.8m.
View
0 to 24 VoltsDC Voltage...
Product available with different options
Home

0 to 24 VoltsDC Voltage Input Sensor

Onset
CABLE-ADAP24
The CABLE-ADAP24 is an external input cable providing analog sensor input of 0-24 Vdc max. for HOBO ZW Series data nodes, UX120, and U12 series data loggers with one or more analog inputs. The cable has 13mm (0.5") tinned braided wire leads and a total length 1.9m (6.3 ft.).
View
HOBO Self-Describing 4 to... HOBO Self-Describing 4 to... 2
Product available with different options
Home

HOBO Self-Describing 4 to 20 mA Input Cable Sensor

Onset
SD-MA-420
For use with HOBO MX1104 and MX1105 multi-channel data loggers, this 4-20 mA input cable offers integrated strain relief to keep it connected to the logger, and it features Self-Describing technology to automatically communicate configuration information to the logger.
View
HOBO Self-Describing...
Product available with different options
Home

HOBO Self-Describing Current Transformer Sensor (range: 2-20, 5-50, 10-100, 20-200,...

Onset
SD-CT-xxx
For use with HOBO MX1104 and MX1105 multi-channel data loggers, this split-core AC current transformer offers integrated strain relief, so the probe is secured to the logger. And it features Self-Describing technology to automatically communicate configuration information to the logger, without any programming or extensive user setup.
View
Current/Voltage

Chat with us on WhatsApp

English

English

Do you need advice?
Product added to wishlist
Product added to compare.

We use our own and third party cookies to obtain statistical data from our users' browsing and to improve our services. If you accept or continue browsing, we consider that you accept its use.